Showing results: 1951 - 1965 of 2630 items found.
-
NEO TELE-TRONIX PVT. LTD
This modern Test Set For Instrument Transformer is used for measuring relative errors of Instrument Voltage and Current Transformers. This is developed for reading out the unbalance of any bridge circuit. It also calculates the burden associated to the test sample. In addition to this, it further converts it to ratio and phase error values for presenting them on a LCD screen. With high-tech microprocessor controller, it ensures to provide quick and correct measurements.
-
DER EE Electrical Instrument
Meter DimensionPlease indicate meter size Internal Resistance250 , 650, 750, 1200 Sensitivity200A , 250A , 500A, 1mA Pointer ColorAs your color request Scale PlateCustom design according to your drawing LampStandard type is 12V/55mA transparent. If you request special specs., please indicate the voltage and current Install position of the level meterVertical or horizontal Popular spec500A/650
-
Aplab Limited
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
Computer Gesteuerte Systeme GmbH
The MCM is designed to drive a variety of brushed motors. This is the CM version of our IMCM. The overload-proof 4-quadrant chopper outputs voltages between 5.5V to 16V up to a constant load of 16A (32A peak). The PWM can be set between 1kHz and 20kHz. The module is protected against undervoltage and overvoltage, shuts down automatically when overheating and is also equipped with a linear current limiting.
-
CM100 -
General Technologies Corp.
Small jaw: 1.2"(W) x 0.53" (D) (300x13.4mm). Clamp opens up to 1/2 inch (12.5 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement from 0.001 up to 100 A. Relative measurement. One touch auto zero
-
HA1600A -
Aim-TTi
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
MCH Instruments Co.,Ltd.
Is a measurement apparatus capable of visually depicting regular changes in electrical activity, such as an electrical current or signal. The resulting data appears as a waveform drawn on a graph with two axes, where the horizontal X axis represents time and the vertical Y axis indicates voltage. In addition, the luminance of the waveform itself is often referred to as the Z axis, which demonstrates the intensity of the activity measured.
-
CT8017 -
General Technologies Corp.
State of the Art ergonomic design and styling for easier handling and use. Full Auto Ranging range selection. Manual range selection function. Large 3 digit LCD display with analog bar graph. AC/DC Voltage measurement up to 600 Volt. Manual or automatic VDC/VAC selection. DC Current measurement up to 10 A. Resistance measurement up to 32 MOhm
-
HH2205F -
Colluck Company Limited
High Accuracy (Basic Accuracy 0.5%). 3-3/4 Jumbo LCD display 4000 count with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V TRMS AC. Higher Current test up to 20A AC/DC. Diode and Continuity check. Measure Resistance up to 40MΩ. Measure Temperature up to 760oC or 1400oF
-
3550 FC -
Fluke Corporation
Condition monitoring sensor to visualize thermal patterns on multiple assets. Maintenance managers can now collect a more comprehensive variety of key-indicator data — thermal imaging, voltage, current, temperature, and power — on critical equipment to build a real-time picture of an asset's condition. With the right mix of data all in one place, managers can implement planned maintenance and decrease the frequency of preventive rounds.
-
MPI-520S -
Sonel S.A.
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
CFL PL4 -
Scope T&M Pvt, Ltd.
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
Analog Devices Inc.
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
XFR Series -
AMETEK Programmable Power, Inc.
XFR is the smart choice for research, product development and production test applications such as R&D, magnet control, product design, ATE, process control, electroplating and burn-in. The unique features of XFR make it the best choice for applications where high power and a wide adjustment of output voltage or current are required in a full 19-inch rack package. Choose from ten 2800-watt models.
-
AMETEK Programmable Power, Inc.
From benchtop supplies to rack mounted industrial power subsystems, AMETEK Programmable Power is the design and manufacturing leader of precision, programmable power supplies. The voltage range for the AMETEK DC bench supplies is 7V to 600V and the current range is 0A to 1,000A producing a power output of 0W to 840W. Select from the models above to find the right fit for your application.